2-8-2 "Mikado" Steam Locomotives in the USA

Deepwater


Class Details by Steve Llanso of Sweat House Media

Class MA (Locobase 10810)

Data from DeGolyer, Volume 28, pp. 127. See also "Baldwin Freight Engine, Deepwater Railway Co.", Railway Master Mechanic, Vol XXX, #1 (January 1906), p. 4-5. (Thanks to Chris Hohl for his 1 October 2021 email correcting the valve gear.) Works numbers were 26625-26626 in October 1905.

The RMM article states that the reason for adopting a 2-8-2 layout was to allow the engine to run in both directions without visiting a turntable. In addition, the report noted that the rear truck "...enables the use of a good depth of throat sheet and also a horizontal grate in the wide fire box."

Baldwin's specs show what would have been regarded at the time as perfectly proportioned as theory then called for. They included a healthy boiler heating surface area/cylinder volume ratio, good ratio of heating surface area to grate area, ideal tube length, spot-on factor of adhesion. Only the firebox heating surface area as a percentage of total seems small.

The Deepwater merged with the Virginian in 1907 and the two Mikados were redesignated MA. Although powerful, the saturated boiler and the small drivers marked the pair as first-generation 2-8-2s. They were soon overmatched by later traffic loads to be moved at higher speeds and eventually were scrapped in December 1933.

Principal Dimensions by Steve Llanso of Middle Run Media
ClassMA
Locobase ID10810
RailroadDeepwater (Virginian)
CountryUSA
Whyte2-8-2
Number in Class2
Road Numbers30-31 / 400-401
GaugeStd
Number Built2
BuilderBurnham, Williams & Co
Year1905
Valve GearStephenson
Locomotive Length and Weight
Driver Wheelbase (ft / m)14 / 4.27
Engine Wheelbase (ft / m)31.08 / 9.47
Ratio of driving wheelbase to overall engine wheelbase 0.45
Overall Wheelbase (engine & tender) (ft / m)59 / 17.98
Axle Loading (Maximum Weight per Axle) (lbs / kg)
Weight on Drivers (lbs / kg)180,000 / 81,647
Engine Weight (lbs / kg)224,000 / 101,605
Tender Loaded Weight (lbs / kg)114,000 / 51,710
Total Engine and Tender Weight (lbs / kg)338,000 / 153,315
Tender Water Capacity (gals / ML)6000 / 22.73
Tender Fuel Capacity (oil/coal) (gals/tons / Liters/MT)10 / 9
Minimum weight of rail (calculated) (lb/yd / kg/m)75 / 37.50
Geometry Relating to Tractive Effort
Driver Diameter (in / mm)51 / 1295
Boiler Pressure (psi / kPa)200 / 1380
High Pressure Cylinders (dia x stroke) (in / mm)22" x 28" / 559x711
Tractive Effort (lbs / kg)45,173 / 20490.15
Factor of Adhesion (Weight on Drivers/Tractive Effort) 3.98
Heating Ability
Tubes (number - dia) (in / mm)300 - 2.25" / 57
Flues (number - dia) (in / mm)
Flue/Tube length (ft / m)18.50 / 5.64
Firebox Area (sq ft / m2)160 / 14.87
Grate Area (sq ft / m2)51 / 4.74
Evaporative Heating Surface (sq ft / m2)3414 / 317.29
Superheating Surface (sq ft / m2)
Combined Heating Surface (sq ft / m2)3414 / 317.29
Evaporative Heating Surface/Cylinder Volume277.11
Computations Relating to Power Output (More Information)
Robert LeMassena's Power Computation10,200
Same as above plus superheater percentage10,200
Same as above but substitute firebox area for grate area32,000
Power L15815
Power MT284.89

Photos

All material Copyright © SteamLocomotive.com
Wes Barris